Emerald Elegance Bracelet
Free Jewelry Making Pattern 

By Kim Connors - www.Bead3.com

Emerald Elegance Bracelet Free Beaded Jewelry Making Pattern
Materials
12 inches of Gold-Colored Buddy Braids
2 – Antique Gold 2mm Crimp Tubes
1 – Antique Gold 17mm Toggle Clasp
6 – Antique Gold 4x10mm Scroll-Work Bead Caps
12 – Antique Gold 1.5x4mm Beaded Rondelles
14 – Emerald AB 6mm Glass Crystal Bicones
3 – Aventurine 10mm Semiprecious Rounds
2 – Aventurine 13x18mm Semiprecious Puff Ovals

Create the Bracelet

1. Take one end of your Buddy Braids wire and thread 1 crimp tube approximately an inch from the end.  Thread the bar end of your toggle clasp.  Thread the end back through the crimp tube.  Using crimping pliers (or any pliers you have) squeeze the crimp bead about a 1/4th of an inch away from the clasp.  See below.  Trim the excess leaving about a half an inch, you will thread the beads over both.

emeb1

2. String the following:

a. 1 – Emerald AB 6mm Crystal Bicone, and 1 – Antique Gold 1.5x4mm Beaded Rondelle.

b. 1 – Emerald AB 6mm Crystal Bicone, 1 – Antique Gold 1.5x4mm Beaded Rondelle, 1 – Emerald AB 6mm Crystal Bicone, 1 – Antique Gold 4x10mm Scroll-Work Bead Cap, 1 – Aventurine 10mm Semiprecious Round, 1 – Antique Gold 4x10mm Scroll-Work Bead Cap, 1 – Emerald AB 6mm Crystal Bicone, 1 – Antique Gold 1.5x4mm Beaded Rondelle, 1 – Emerald AB6mm Crystal Bicone, 1 – Antique Gold 1.5x4mm Beaded Rondelle, 1 – Aventurine 13x18mm Semiprecious Oval, and 1 – Antique Gold 1.5x4mm Beaded Rondelle.

c. Repeat Pattern in Step (b.) 1 time.

d. 1 – Emerald AB 6mm Crystal Bicone, 1 – Antique Gold 1.5x4mm Beaded Rondelle, 1 – Emerald AB 6mm Crystal Bicone, 1 – Antique Gold 4x10mm Scroll-Work Bead Cap, 1 – Aventurine 10mm Semiprecious Round, 1 – Antique Gold 4x10mm Scroll-Work Bead Cap, 1 – Emerald AB 6mm Crystal Bicone, 1 – Antique Gold 1.5x4mm Beaded Rondelle, 1 – Emerald AB6mm Crystal Bicone, 1 – Antique Gold 1.5x4mm Beaded Rondelle, and 1 – Emerald AB 6mm Crystal Bicone

3. Thread 1 crimp tube and the round part of your toggle clasp.  Thread the wire back through the crimp bead after going through the loop on the toggle clasp.  Thread the wire through several beads (see below).  Using your pliers, squeeze the crimp tube about a 1/4th of an inch away from the clasp.  Trim the excess wire as close to the bead as you can. 

emeb2

You are done!!  These directions make a bracelet that is approximately 8 inches long.  If you need to change the length just add or subtract beads.  You can use this pattern with any color beads you wish!!

We hope you enjoyed this beading project!  For more beads and supplies please shop on our website at www.Bead3.com.

Add Comment

Mailing List

Items